[20220812_142139_user] D2_main.c

[20220812_142139_user] D2_main.c

@@ -0,0 +1,346 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file           : main.c
+  * @brief          : Main program body
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the License; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        www.st.com/SLA0044
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+#include "adc.h"
+#include "usart.h"
+#include "i2c.h"
+#include "tim.h"
+#include "stm32f4xx_hal.h"
+#include "gpio.h"
+#include "stdio.h"
+
+/* Private variables ---------------------------------------------------------*/
+
+/* Private variables ---------------------------------------------------------*/
+#define VECT_TAB_OFFSET  0x10000
+int tankstatus = 0;
+uint8_t zigbeecmd1[5]={0xFE,0x00,0x01,0x00,0x01};
+uint8_t zigbeecmd2[5]={0xFE,0x00,0x02,0x00,0x02};
+uint8_t zigbeestatu[20];
+uint8_t zigbeestatu1[5];
+uint8_t zigbeecon[7]="connect";
+uint8_t zigbeenotcon[11]="not connect";
+uint8_t zigbeechang[14]="change is down";
+uint8_t cmd[7]={0xFF,0x00,0x00,0x00,0x00,0x00,0x0D};
+HAL_StatusTypeDef Status;
+#define ADDR_AT24C04_WRITE_FIRST_16_PAGES 0xEC
+#define ADDR_AT24C04_WRITE_FIRST_16_PAGES 0xEC
+#define ADDR_AT24C04_READ 0xED
+#define AT24C04_TIMEOUT 0xED
+#define AT24C04_PAGE_SIZE 16
+#define BUFFER_SIZE 1
+uint16_t dig_T1;
+uint16_t dig_T2;
+uint16_t dig_T3;
+uint16_t dig_P1;
+uint16_t dig_P2;
+uint16_t dig_P3;
+uint16_t dig_P4;
+uint16_t dig_P5;
+uint16_t dig_P6;
+uint16_t dig_P7;
+uint16_t dig_P8;
+uint16_t dig_P9;
+uint32_t adc_P=0;
+uint32_t adc_T=0;
+uint8_t WriteBuffer[BUFFER_SIZE]={0xb6};
+uint8_t WriteBuffer1[BUFFER_SIZE]={0xff};
+uint8_t WriteBuffer2[BUFFER_SIZE]={0x00};
+uint8_t ReadBuffer[BUFFER_SIZE];
+int RH;
+float M15_BMP280 =0;
+/* USER CODE BEGIN PV */
+typedef  void (*pFunction)(void);
+/* USER CODE END PV */
+/* Private function prototypes -----------------------------------------------*/
+void SystemClock_Config(void);
+void MX_ADC1_Init1(char pin);
+void sensor(void);
+HAL_StatusTypeDef AT24C04_Write(I2C_HandleTypeDef *hi2c,uint16_t MemAddress,uint8_t *pData);
+HAL_StatusTypeDef AT24C04_Read(I2C_HandleTypeDef *hi2c,uint16_t MemAddress,uint8_t *pData);
+long bmp280_T_MultipleReadThree(void);
+long bmp280_P_MultipleReadThree(void);
+short bmp280_MultipleReadTwo(uint16_t addr);
+/* USER CODE BEGIN PFP */
+/* USER CODE END PFP */
+/* Private user code ---------------------------------------------------------*/
+/* USER CODE BEGIN 0 */
+int _write(int fd, char *ch, int len)
+{
+   HAL_UART_Transmit(&huart4, (uint8_t*)ch, len, 0xFFFF);
+   HAL_UART_Transmit(&huart2, (uint8_t*)ch, len, 0xFFFF);
+   return len;
+}
+void print(char* s, float c)
+{   int w;
+    int w_d;
+    int w_f;
+    if(c<0)
+    {
+       w = c*100;
+       w_d = w/100;
+       w_f = (-1*w)%100;
+    }
+    else
+    {
+      w = c*100;
+      w_d = w/100;
+      w_f = w%100;
+    }
+    printf("%s = %d.%d\n",s,w_d,w_f);
+}
+/* USER CODE END 0 */
+/**
+* @brief  The application entry point.
+* @retval int
+*/
+int main(void)
+{
+  SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET;
+  HAL_Init();
+  SystemClock_Config();
+  MX_GPIO_Init();
+  MX_USART2_UART_Init();
+  MX_UART4_Init();
+  MX_USART1_UART_Init();
+  HAL_UART_Transmit(&huart2, (uint8_t *)zigbeecmd2, sizeof(zigbeecmd2), 10);
+  HAL_Delay(1000);
+  HAL_UART_Transmit(&huart2, (uint8_t *)zigbeecmd1, sizeof(zigbeecmd1), 10);
+  HAL_UART_Receive(&huart2, (uint8_t *)zigbeestatu,sizeof(zigbeestatu),2000);
+  HAL_UART_Transmit(&huart4, (uint8_t *)zigbeestatu, sizeof(zigbeestatu),10);
+  if (zigbeestatu[18]== 0x01 || zigbeestatu[18]== 0x02)
+  {
+     HAL_UART_Transmit(&huart4, (uint8_t *)zigbeecon, sizeof(zigbeecon),10);
+  }
+  else if(zigbeestatu[18]== 0x05)
+  {
+     HAL_UART_Transmit(&huart4, (uint8_t *)zigbeenotcon, sizeof(zigbeenotcon),10);
+  }
+  AT24C04_Write(&hi2c1,0xe0,WriteBuffer);
+  AT24C04_Write(&hi2c1,0xf4,WriteBuffer1);
+  AT24C04_Write(&hi2c1,0xf5,WriteBuffer2);
+  dig_T1 = bmp280_MultipleReadTwo(0x88);
+  dig_T2 = bmp280_MultipleReadTwo(0x8A);
+  dig_T3 = bmp280_MultipleReadTwo(0x8C);
+  dig_P1 = bmp280_MultipleReadTwo(0x8E);
+  dig_P2 = bmp280_MultipleReadTwo(0x90);
+  dig_P3 = bmp280_MultipleReadTwo(0x92);
+  dig_P4 = bmp280_MultipleReadTwo(0x94);
+  dig_P5 = bmp280_MultipleReadTwo(0x96);
+  dig_P6 = bmp280_MultipleReadTwo(0x98);
+  dig_P7 = bmp280_MultipleReadTwo(0x9A);
+  dig_P8 = bmp280_MultipleReadTwo(0x9C);
+  dig_P9 = bmp280_MultipleReadTwo(0x9E);
+  while (1)
+  {
+    sensor();
+    if(M15_BMP280<16)
+    {
+         HAL_GPIO_WritePin(GPIOA,GPIO_PIN_10, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOA,GPIO_PIN_8, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOD,GPIO_PIN_15, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOD,GPIO_PIN_13, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOD,GPIO_PIN_11, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOB,GPIO_PIN_15, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOE,GPIO_PIN_15, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOE,GPIO_PIN_13, GPIO_PIN_RESET);
+
+         HAL_GPIO_WritePin(GPIOE,GPIO_PIN_11, GPIO_PIN_RESET);
+
+    }
+  }
+}
+void SystemClock_Config(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  __HAL_RCC_PWR_CLK_ENABLE();
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLM = 8;
+  RCC_OscInitStruct.PLL.PLLN = 72;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+  RCC_OscInitStruct.PLL.PLLQ = 3;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
+  {
+    Error_Handler();
+  }
+}
+void user_pwm_setvalue(uint16_t value)
+{
+    TIM_OC_InitTypeDef sConfigOC;
+    sConfigOC.OCMode = TIM_OCMODE_PWM1;
+    sConfigOC.Pulse = value;
+    sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
+    sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
+    HAL_TIM_PWM_ConfigChannel(&htim2, &sConfigOC, TIM_CHANNEL_1);
+    HAL_TIM_PWM_Start(&htim2, TIM_CHANNEL_1);
+}
+void user_pwm_setvalue2(uint16_t value)
+{
+    TIM_OC_InitTypeDef sConfigOC;
+    sConfigOC.OCMode = TIM_OCMODE_PWM1;
+    sConfigOC.Pulse = value;
+    sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
+    sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
+    HAL_TIM_PWM_ConfigChannel(&htim2, &sConfigOC, TIM_CHANNEL_2);
+    HAL_TIM_PWM_Start(&htim2, TIM_CHANNEL_2);
+}
+void sensor(void)
+{
+    adc_T=bmp280_T_MultipleReadThree();
+    adc_P=bmp280_P_MultipleReadThree();
+    double var1, var2,t_fine;
+    var1 = (((double) adc_T) / 16384.0 - ((double) dig_T1) / 1024.0)* ((double) dig_T2);
+    var2 = ((((double) adc_T) / 131072.0 - ((double) dig_T1) / 8192.0)* (((double) adc_T) / 131072.0 - ((double) dig_T1) / 8192.0))* ((double) dig_T3);
+    t_fine = (int32_t) (var1 + var2);
+    double temperature = (var1 + var2) / 5120.0;
+    double pressure;
+    var1 = (t_fine / 2.0) - 64000.0;
+    var2 = var1 * var1 * ((double) dig_P6) / 32768.0;
+    var2 = var2 + var1 * ((double) dig_P5) * 2.0;
+    var2 = (var2 / 4.0) + (((double) dig_P4) * 65536.0);
+    var1 = (((double) dig_P3) * var1 * var1 / 524288.0+ ((double) dig_P2) * var1) / 524288.0;
+    var1 = (1.0 + var1 / 32768.0) * ((double) dig_P1);
+      if (var1 == 0.0)
+      {
+         var1 = 0;
+      }
+    pressure = 1048576.0 - (double) adc_P;
+    pressure = (pressure - (var2 / 4096.0)) * 6250.0 / var1;
+    var1 = ((double) dig_P9) * pressure * pressure / 2147483648.0;
+    var2 = pressure * ((double) dig_P8) / 32768.0;
+    pressure = pressure + (var1 + var2 + ((double) dig_P7)) / 16.0;
+    cmd[1]=pressure/10000; 
+    int pa =pressure;
+    cmd[2]=(pa%10000)/100;
+    cmd[3]=(pa%10000)%100;
+    HAL_UART_Transmit(&huart4, (uint8_t *)cmd, sizeof(cmd),1);
+    HAL_Delay(10000);
+}
+HAL_StatusTypeDef AT24C04_Write(I2C_HandleTypeDef *hi2c,uint16_t MemAddress,uint8_t *pData)
+{
+       Status = HAL_I2C_Mem_Write(&hi2c1, ADDR_AT24C04_WRITE_FIRST_16_PAGES, MemAddress, I2C_MEMADD_SIZE_8BIT, pData, AT24C04_PAGE_SIZE, AT24C04_TIMEOUT);
+       return Status;
+}
+HAL_StatusTypeDef AT24C04_Read(I2C_HandleTypeDef *hi2c,uint16_t MemAddress,uint8_t *pData)
+{
+   Status = HAL_I2C_Mem_Read(&hi2c1, ADDR_AT24C04_READ, MemAddress, I2C_MEMADD_SIZE_8BIT, pData, BUFFER_SIZE, AT24C04_TIMEOUT);
+   return Status;
+}
+  long bmp280_T_MultipleReadThree()
+{
+     uint8_t msb, lsb, xlsb;
+     int32_t temp = 0;
+     AT24C04_Read(&hi2c1,0xfa,ReadBuffer);
+     msb=ReadBuffer[0];
+     AT24C04_Read(&hi2c1,0xfb,ReadBuffer);
+     lsb=ReadBuffer[0];
+     AT24C04_Read(&hi2c1,0xfc,ReadBuffer);
+     xlsb=ReadBuffer[0];
+     temp = ((msb << 12)|(lsb << 4)|(xlsb >> 4));
+     return temp;
+}
+long bmp280_P_MultipleReadThree()
+{
+   uint8_t msb, lsb, xlsb;
+   int32_t pressure = 0;
+   AT24C04_Read(&hi2c1,0xf7,ReadBuffer);
+   msb=ReadBuffer[0];
+   AT24C04_Read(&hi2c1,0xf8,ReadBuffer);
+   lsb=ReadBuffer[0];
+   AT24C04_Read(&hi2c1,0xf9,ReadBuffer);
+   xlsb=ReadBuffer[0];
+   pressure = ((msb << 12)|(lsb << 4)|(xlsb >> 4));
+   return pressure;
+}
+  short bmp280_MultipleReadTwo(uint16_t addr )
+{
+   uint8_t msb, lsb;
+   uint16_t temp = 0;
+   AT24C04_Read(&hi2c1,addr,ReadBuffer);
+   lsb = ReadBuffer[0];
+   AT24C04_Read(&hi2c1,addr+1,ReadBuffer);
+   msb = ReadBuffer[0];
+   temp = msb << 8|lsb;
+   return temp;
+}
+void MX_ADC1_Init1(char pin)
+{
+  ADC_ChannelConfTypeDef sConfig = {0};
+  hadc1.Instance = ADC1;
+  hadc1.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV2;
+  hadc1.Init.Resolution = ADC_RESOLUTION_12B;
+  hadc1.Init.ScanConvMode = DISABLE;
+  hadc1.Init.ContinuousConvMode = DISABLE;
+  hadc1.Init.DiscontinuousConvMode = DISABLE;
+  hadc1.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;
+  hadc1.Init.ExternalTrigConv = ADC_SOFTWARE_START;
+  hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT;
+  hadc1.Init.NbrOfConversion = 1;
+  hadc1.Init.DMAContinuousRequests = DISABLE;
+  hadc1.Init.EOCSelection = ADC_EOC_SINGLE_CONV;
+    if (HAL_ADC_Init(&hadc1) != HAL_OK)
+    {
+      Error_Handler();
+    }
+  sConfig.Channel = pin;
+  sConfig.Rank = 1;
+  sConfig.SamplingTime = ADC_SAMPLETIME_3CYCLES;
+  if (HAL_ADC_ConfigChannel(&hadc1, &sConfig) != HAL_OK)
+  {
+    Error_Handler();
+  }
+}
+void MX_GPIO_Input1(unsigned long pin)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  __HAL_RCC_GPIOE_CLK_ENABLE();
+  GPIO_InitStruct.Pin = pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = GPIO_PULLDOWN;
+  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+}
+void Error_Handler(void)
+{
+}